# Simple Transformer-less Inverter Circuit – 1000 Watt

In this post we are going to learn how to construct a simple transformer-less inverter circuit which can power loads up to 1000 watts.

**We will see:**

**What is Transformer-less inverter?****Advantages of transformer-less inverter****Stages of Proposed Transformer-less inverter****Circuit Diagram****Block Diagram****How to Test and Operate this Circuit****RMS calculation of this Inverter**

**What is Transformer-less Inverter?**

As the name suggests, the inverter is not equipped with a standard step-up transformer like traditional inverter for converting low voltage AC to high voltage AC.

Transformer-less inverters utilizes high voltage DC as input which is converted to high voltage AC output by oscillators and H-bridge drivers, since there is no transformer great efficiency more than 97% is achievable, the only loss is from the MOSFETs of H-bridge. The high voltage DC source can be solar panels or battery.

As the transformer-less inverter cannot boost the voltage to power nominal 230V/120VAC appliances, DC current of 120V or 230V or more is applied at input.

**Brief Insight on High Frequency Transformer Inverter:**

There are products marketed as transformer-less inverter with a tiny transformer in it, which can step-up from 12VDC to 230VAC, these are called high frequency transformer inverter, but they are not truly transformer-less, yet the terms can used interchangeably, since the real life efficiency, weight and other advantages are similar.

You can build a High Frequency Transformer Inverter Circuit, click here

The high frequency transformer works like this: The low voltage DC is converted to high frequency AC and step-up by the tiny ferrite core transformer, ferrite core transformer can handle much higher power at better efficiency than bulky iron core low frequency transformer.

The high frequency AC is converted to high voltage DC around 320V and fed to high voltage H-bridge and switched at 50/60Hz in sine PWM form or SPWM form and you get 230VAC sine wave.

The high frequency transformer inverters are not bad either, they offer light weight and good efficiency above 90%.

Now you know the difference between a true transformer-less inverter and high frequency inverter which looks like transformer-less.

**Advantages of Transformer-less inverter:**

In this section we are going to understand why we need a transformer-less inverter, this can also be applied to high frequency transformer inverters.

Transformer-less inverter are relatively inexpensive due to absence of bulky iron core transformer which is the most expensive part of the inverter and now, there are no losses related to transformer so more efficiency.

Now the inverter gets lighter and makes it portable which makes less challenging to install.

**Stages of Proposed Transformer-less Inverter Circuit:**

The proposed inverter is very simple, it consists of stages:

**DC Power Source/Battery Bank****Oscillator / Multivibrator****H-Bridge**

**Full Circuit Diagram:**

**Circuit Update:**

We have designed yet another best Transformerless inverter circuit which can output modified sine wave at 230VAC,click herefor the circuit diagram.

**Block Diagram of Transformer-less Inverter Circuit:**

**DC power source:**

The power source / battery bank consists of (12V 7Ah) 19 batteries connected in series. A fresh fully charged lead acid battery reads 13V so **13 x 19 = 247 VDC output.**

The combined 19 batteries gives total power of **12V x 7Ah x 19 = 1596 watt hour (Wh) **of energy.

For those who home’s power supply is 120VAC, you can connect (12V 7Ah) 10 batteries in series.

Which gives **13V x 10 = 130VDC**.

The combined 10 batteries give total power of **12V x 7Ah x 10 = 840 Watt** **hour **(Wh).

The excess battery voltage will get drop due to the MOSFET and you will get nominal operating voltage of 230V and 120VAC.

When the battery reaches 11.1V per battery you can consider it as low battery condition.

The AC voltage output at low battery will be **11.1 x 19 = 210.9V** or **11.1 x 10 = 111V**

So from full battery to low battery condition the output varies approximately 36V for 230V system and 18V for 120V system. The connected electronic appliances will happily work in that voltage ranges.

You can also replace batteries with appropriate rated solar panels.

NOTE: There is a separate 12V battery for the oscillator.

**Oscillator:**

The oscillator is the circuit which generates appropriate waveform for the inverter’s output. Here we are using a simple Astable multivibrator using NPN transistors. The oscillator is powered separately from a 12V battery.

The circuit is tuned to generate 50Hz square wave output but due to the tolerance of the resistor and capacitor network we will get close to 50Hz. For 60Hz you can replace R2 and R3 resistors with 25K ohm resistor.

You may also Interested in: Simple IC 555 Inverter Circuit

The frequency of this Astable multivibrator can be calculated by:

**F = 1 / 1.38 x R x C**

Where,

F is the Frequency in Hz

C is capacitance in farad

R is resistance in ohm

**Output of this Astable multivibrator circuit:**

**H-bridge:**

The H-bridge is the one which converts the high voltage DC to high voltage AC current, the oscillator switches the H-bridge.

The H-bridge consists of four power MOSFETs, couple of IRF740 and couple of IXTP10P50P which are rated at 400V 10A and -500V -10A respectively, which is enough for this inverter.

** Now let’s see how an H-bridge functions:**

The H-bridge changes the polarity across the load which makes direct current to alternating current.

In the left image above, S1 and S3 are closed, now the power flows from S1 to load and through S3 to complete the circuit, note the polarity across the load.

Now look at the right image above, the S2 and S4 are closed. Now the power flows from S4 then to the load and completes the circuit through S2, now look at the polarity across the load which is reversed from previous cycle.

You may also interested in: Simple Modified Sine Wave Inverter Circuit – IC 555

This cycle continues and generates alternating current in square wave form.

At no instant S1 and S2 should be ON simultaneously, if such instants occur it will lead to short circuit, this is same with S3 and S4.

**The switches are replaced with MOSFETs as shown below:**

At points “A” and “B” where the oscillator’s input is applied. A fuse is placed at +Ve rail of high voltage input to avoid short circuit.

**Specifications of MOSFETs:**

**IRF740 N-Channel MOSFET:**

- Voltage Drain to Source (Vds):
**400V** - Voltage Gate to Sourec (Vgs):
**+/-20V (Max)** - Continues Drain Current:
**10A (Continuous)**

**IXTP10P50P P-Channel MOSFET:**

- Voltage Drain to Source (Vds):
**-500V** - Voltage Gate to Sourec (Vgs):
**+/-20V (Max continuous)**

- Continues Drain Current:
**-10A (continuous)**

Note: If you couldn’t find exact MOSFETs you can substitute with any equivalent specification.

**How to Test and Operate this Circuit:**

You need not to purchase the 19 (12V 7Ah) batteries to test the proper operating of this inverter circuit. You can do this in inexpensive way, follow the instructions below:

- Construct the circuit fully with necessary fuse and switches.
- Purchase 28 (fresh 9V batteries) one for the oscillator circuit and 27 for H-bridge.
- Connect the 27 (9V batteries) in series in this manner (it will be a lengthy battery):

- Solder the +Ve and –Ve with thick wires. Now connect the battery terminals to a 40 Watt 230V tungsten bulb. It should glow at full brightness. If it glows, you have connected the batteries properly.
- Now connect the high voltage DC from battery to H-bridge and connect the separate 9V battery to the oscillator and connect the 40 Watt bulb as load at H-bridge.Now, turn ON the oscillator by pushing/sliding “switch 1” first and then turn on the “switch 2” which will power the H-bridge. Reversing the switching sequence may lead to short-circuit.
- As soon as you turn ON the switch 2 the light bulb should glow immediately at full brightness, now your inverter is ready. Now, you can test with other AC loads.

**RMS calculations for this Inverter:**

Let’s understand what RMS is and why we need to consider in AC current.

Did you know that your 230VAC at your home are not actually 230V peak to peak but, 320V peak to peak? When we say 230VAC, we talk about the average value of the peak to peak amplitude of the AC current or RMS value in short.

Let’s we understand with an example:

If you have a bulb rated at 230V, you are powering it by using 230VDC and sine wave 230VAC peak to peak, which type of current will make the bulb glow brighter, AC or DC?

The right answer is DC with 230V. The AC 230V peak to peak is equivalent to 162V which is the RMS; if you measure the 230V peak to peak with voltmeter it will read 162V. In this case the bulb will glow at the brightness of 162V.

To glow the bulb at same brightness as 230VDC we have to apply peak to peak 320V for sine wave and now the voltmeter will read 230VAC.

**RMS for sine wave is calculated by:**

**RMS = Vpk / square_root(2) **where, Vpk is peak to peak voltage.

If it is not pure sine wave, there will be deviations in calculated value. Different waveforms will have different RMS formals.

Now let’s see the same for square wave, and should we apply more than 240 voltage at input to get nominal operating voltage (RMS) of 230/120VAC?

The RMS of square wave is given by:

**Vrms = Vpk x square_root (F x T)**

*Where,*

*Vpk is peak to peak voltage*

*F is the frequency*

*T is the time period*

For square wave with 50% duty cycle the square_root (F x T) is always = 1.

So the equation becomes **Vrms = Vpk **(RMS is same as peak to peak value of square wave)

Here we are inputting voltages approx. 240V from batteries, so the RMS at the AC output will also be 240VAC (for square wave). If we were applying pure sine wave to H-Bridge then we have to apply 320VDC at input to get 230VAC output. Similarly different voltage at input if we apply modified sine wave to H-bridge.

**Advantage of this inverter circuit:**

**Simple circuit design with few components****High efficiency greater than 90%****Solar panel compatible****No need for automatic voltage regulation for most part, as the AC load is directly placed on battery.**

**Disadvantage of this inverter circuit:**

**Square wave is not suitable many medical and sensitive electronics equipments.****Need huge battery bank / long solar panel array to meet the voltage needs.****Need separate battery source for oscillator.****Battery discharge rate affects output AC voltage (240V to 210V).**

*If you have any question regarding this project, please feel free to express in the comment, you can anticipate a guaranteed reply from us.*

**Top Comment:**

Sir

I am an electronic engineering student,

I have designed exactly the same inverter, i have supply of Solar panels 240 vdc, and i run 7 amperes load continuously successful,……………..

Plzz–

Basit

GOOD

Thanks.

Can this 7Ah withstand test of time

Hi,

You can test your built by connecting several 9V batteries in series to get 240VDC for H-bridge (you need separate 12VDC for the oscillator). Once you get the satisfied result you can purchase expensive batteries for your installation. All explanations are given in detail.

Regards

Good circuit.

thanks i was searching this project

You are welcome!

Hi, can we use a 100w or 200w battery directly for this inverter? If yes, how many hours will it take to drain the battery? Thanks.

Hi Yusuf,

You mean 100Ah / 200Ah? There is nothing called 100W or 100 Watt battery or are you asking for 100V or volt battery? If so, yes you can… it will give you 5 to 10V less at the output than your battery Voltage. To answer how long you can power your load, it depends on the combined Ah rating of the battery. A 1 Ah, 200V battery will power the load of 200V for one hour, if it draws 1 Ampere from battery.

If you are seriously building this inverter please test the inverter with several 9V batteries in series as mentioned in this post and only after successful build you may switch to bigger batteries.Regards

I mean 100/200Ah and not wattage. Anyway, you have answered my question. God bless you sir.

What happens if you convert 3 phase A.C to D.C required by the inverting circuit can it work .without using batteries…. Note that for converting A.C to DC using rectifiers full bridge

Hi Coaster,

Can you elaborate your question, I can’t understand clearly…

Regards

I’m actually looking for a 12v – 12v inverters circuit, by which I mean 12 v DC in and 12v AC out.

The load in my case is an electromagnet that I want to have an alternating polarity of the magnet.

Is there anything worth scaling down given the low voltages?

The load will be 12v 3A – basically a bunch of 12v 250ma Solenoids wired in parallel.

Any advice?

Hi John,

Yes, It is possible, we need a multivibrator circuit to produce frequency greater than 50/60 Hz (it depends on the coil specs so that we can achieve maximum field strength), A H-bridge setup will energize the electromagnet in alternating polarity. Just apply 12V to the given circuit still you will achieve a decent result. My suggestion is to use two N-type two P-type H-bridge (IRF540 and IRF9540 respectively) and follow the circuit, use same 12V source for powering multivibrator and H-bridge.

Regards

Good day. Blogthor. I really appreciated your efforts you are gave sacrificed to write the above articles. My question here is that, can someone step up the 12V Battery @100 – 200AH to 220VDC instead of combine multiple battery to get up to 220VDC, using ferrite core. If yes, how can someone go about it since ferrite core operatd s at a very high frequency. Pls can you give analysis on how to go about it. I will be expecting your response. Thanks.

Hi Engr,

Yes, we can step-up 12VDC to 230VAC using ferrite core transformer. The 12VDC is converted to 12VAC at several KHz and applied to a ferrite core transformer. Now the transformer outputs 230VAC at several KHz, this converted to 230VDC using rectifier, now the 230VDC is applied to a similar circuit given in this post (with high voltage MOSFETs). The ferrite core based inverters are also touted as transformerless inverters and their efficiency are also exceptional.

Best Regards

Who can I contact for a 3000W Sinewave Inverter diagram to be used with solar panels

Sorry, I don’t know any one to get contact. My suggestion would be buy a ready-made inverter from market, designing and construction will cost you a lot.

Regards

good circuit blogthor … but if i need to convert 12v DC to 220v AC with same 4 mosfet what different will happen in component?

Hi Eslam,

You need a transformer to step-up 12V to 220V.

Regards

Hello,

On the above circuit, can i used N channel Mostfet to substitute instead of the p Channel mosfet and what arrange will the mosfet circuit bee now.

Thanks

Hello Paul,

You need to bootstrap the N-channel MOSFETs that you are replacing P- channel MOSFETs.

Regards

Ok sir, Thank you very much for your support

Sir

I am an electronic engineering student,

I have designed exactly the same inverter, i have supply of Solar pannels 240 vdc, and i run 7 amperes load continuesly successful, so now i am trying to convert square wave to sine wave out put, what is your suggestion.

Plzz

Hi basit,

First of all congratulations for making a working transformerless inverter.

If possible please share your inverter images with us, I will publish here with your credits.

Now coming to your question, square wave cannot be converted into sine wave. You can try by adding LC filters but when you load it, the waveform get distorted.

We have designed a transformerless modified sinewave inverter in this site you may try that one to improve output quality.

Regards

Dear blogthor,

Is it possible to power the oscillator from 220VDC source without using additional 12V battery? Maybe to implement a circuit with darlington pair? Do you have effective solution here?

Thanks

Yes, you can but you need to step down 220VDC to 12VDC somehow if you don’t want to use a separate battery for the oscillator.

There is no need for any darlington pair in the oscillator.

Hi sir! Im planning to build my school project similar to this project which is also a tranformerless inverter (1000W transformerless inverter). But I supposed to have a pure since wave output. What should I do to make my Oscillator produce a pure sine wave? And also how am I going to calculate the low battery condition if I have #V DC supply (from solar pannels)? Is there any formula for that?

Hi Adrian,

Currently we don’t have a pure sine wave design but, we have modified sine wave transformerless inverter: https://electronics-project-hub.com/transformerless-inverter-circuit/

The pure sine wave design is not a single change that you can make to your existing design, its much more complicated than that. We will consider your request in future.

Regards

How about the low battery condition sir? How am I supposed to calculate that? If my batteries or dc supplies are in low battery condition already? For me to be aware of the minimum and maximum range of my dc supplies to make my inverter operates normally. By the way, english is not my native laguage. I hope you understand what Im trying to say. Thank you sir! This projects helps me a lot.

Hi again,

You did not mention the type of battery.

If you are powering the inverter using batteries, then usually we would use 12V lead acid batteries in series. For 12V lead acid batteries 11.1V is considered as low voltage and 13 to 13.5V as full battery. You can see all the calculation given below the block diagram.

If you are powering the circuit directly from solar panels then low voltage situation depends on the type of load. Some loads like chargers / TV that uses SMPS can operate as low as 100V, but heaters / filament lamps / motors need 220VAC to operate optimally. Since we use all these load simultaneously we should not allow output go too low.

I have seen inverters/UPS in commercial buildings kick in when AC voltage goes below 170V-180V. So we can safely assume anything below 170V is low voltage for 220V AC loads.

Regards

i’m an electrical engineering student sir, my problem is i can’t find the IXTP10P50P on my multisim. what is the alternative of IXTP10P50P? i really need your help sir because this is my research project.

Hi Anna,

If you could not find the mentioned P-Channel MOSFET try to find any other high voltage P-channel MOSFET that is rated for 300V or above.

OR

You can use IRF740 with bootstrapping, follow this circuit for MOSFET stage: https://electronics-project-hub.com/wp-content/uploads/2019/04/Boot-strapped-H-bridge_bb-768×618.jpg

Regards

Blogthor,

I have been reading your transformeless inverter threads with keen/kin? interest. I have a small genset which produces about 400VAC in the absence of a damaged factory inverter. I need to use this 400VAC by converting it to plus/minus 400VDC. The wiring output is in Star formation without a neutral point. Kindly assist me by return e-mail and blog with a rectifier (diode based) circuit to couple to https://electronics-project-hub.com/simple-transformer-less-inverter-circuit-1000-watt/ as the V-DC input.

Sorry, presently we don’t have such inverter design with the specifications you mentioned.

In the formula you gave for calculating frequency which is F = 1/1.38xRxC, what do you mean by R? Which R? 27k ohms? 1k ohms? The summation of all resistance? And also what do you mean by C? The summation of all capacitance? I tried trial and error for the values of those variables and I cant get a 50 Hz result. How did you get 50 Hz? Can you explain the solution? Thank you sir!

Calculation goes like this:

1/1.38 x 27 x 10^3 x 0.47 x 10^-6 = 57.10 Hz (for ideal components)

But practically we are getting around 50Hz (51.33Hz) on the scope. Theoretical calculations are

NOT EQUALto practical outputs.Thanks for the way u ‘ve been solving electronics projects problems.Pls, l need a working 1000w inverter circuit diagram using irf 150 mosfet.

Hi, If possible in future we will post a project!

Hello Sir,

I need 100khz frequency and 1 amper in output. Can i use this circuit?

Can use transformer and diode bridge instead of battery to make 240vdc?

Can you please elaborate your question…..

yes, sure. Is that possible I use diode bridge and capacitor in input instead 19 batteries to make 240vdc?

and also, i would like to know, Is this circuit produce 1ookhz and 1 amper in output? I need this information for Plasma generator!

Thank you again

You can provide 240VDC input from any source, but my suggestion is that never connect it to mains supply.

It can output 100KHz, but you need to recalculate the RC values to generate 100KHz using this formula F = 1 / 1.38 x R x C

The current output depends on your current input.

Regards